Stainless Strip for Stamping Terminals: 5 Specs to Lock Down

 

A terminal is a small part with a lot of inherited decisions, and five of them arrive inside the coil. Here is the five-lock specification we would write for a stamping programme.

Direct answer

  • Lock the grade and the standard. Our published precision 304 stainless steel strips carry ASTM/AISI, GB, JIS, EN and KS, and the same grade is written 304, 06Cr19Ni10, SUS304 or 1.4301.
  • Lock the temper, because stainless cannot be tempered by you. Published hardness runs annealed, 1/4H, 1/2H, 3/4H and H, and 304 work hardens but cannot be heat hardened.
  • Lock the dimensional band, not the nominal. Thickness runs 0.03 mm to 4.0 mm and width 10 mm to 1500 mm, with slit width tolerance of plus or minus 0.2 mm.
  • Lock the surface condition. Published finishes are 2B, BA, 2D, HL, No.4 and 8K, with PVC film and paper interleaving, because a roll mark pressed into a terminal survives plating.
  • Lock the edge and the paperwork. Edge is published as slit edge or mill edge, and the certificate should carry composition, mechanical results for the delivered temper and the heat number.
  • These are five lines, not five documents. An order that states all five can be repeated by a second supplier and checked on arrival.
Cold-rolled stainless steel coil wound tightly and banded with steel straps, the delivery form in which precision strip reaches a stamping line
Precision strip arrives as a banded coil, and every one of the five specifications below is settled before that coil is fed.

Everything below comes from our own published specification, on the precision stainless steel strip range and the precision 304 stainless steel strips product. It is written for the buyer who must run the same parts on the same press next year: the coil decides whether stamping, forming and plating behave alike on every shift.

Why Terminal Stamping Breaks on Specs Nobody Wrote Down

Terminal programmes fail in a familiar way. The drawing is correct, the die is correct, and then a coil arrives that is slightly harder or thicker than the coil before it. The press runs, the parts look acceptable, and three weeks later the line is producing terminals that are out of flat, that crack in the bend radius, or that carry a surface defect the plating line reproduces on every part in the box.

All of it is an unspecified variable, because the purchase order usually says “304 stainless steel strip, 0.3 mm” and stops there. A specification that also names the standard, the temper, the tolerance band, the surface condition and the certificate set is a purchase, and it can be repeated. Five locks are enough for a terminal, because the part itself is shallow, cold formed and plated.

Spec 1: Grade and the Standard Designation You Buy Against

Our published 304 product lists the standards it is supplied against as ASTM/AISI, GB, JIS, EN and KS, and shows the grade written five ways in the same table: 304, 06Cr19Ni10, SUS304, 1.4301 and STS304. The grade alone does not tell a supplier which acceptance band to run, because the band lives in the standard.

So write both. ASTM A240/A240M carries the chromium and chromium-nickel stainless plate, sheet and strip grades, and naming it anchors the certificate, the chemistry limits and the mechanical expectations to something the supplier and your inspector already know. A line that only says “304″ can be answered with a domestic grade and a domestic certificate, and your inspector then checks your terminals against a document you never specified.

The published metallurgy matters here. Our 304 description gives a minimum of 18 percent chromium and 8 percent nickel, notes that the grade can still show magnetic properties after cold working, and states that it work hardens and cannot be hardened by heat treatment. That last point decides the next lock: the strength you get is the strength of the cold work.

Spec 2: Temper and Hardness, Which You Cannot Change Later

The published hardness options are annealed, 1/4H, 1/2H, 3/4H and H, and the hard precision strip range extends the set through FH, EH and SH for tighter applications. Leaving temper out looks like a soft detail until the first terminal cracks in the bend radius, at which point it looks like an expensive one.

Because 304 cannot be hardened by heat treatment, temper is a property you buy rather than a condition you impose. An annealed coil forms easily and springs back, a half-hard coil holds a bend and pays for it in the spring-back angle your die has to absorb, and a hard coil behaves closer to a spring itself. Each is correct for a different terminal, and none is interchangeable once the part is drawn.

The line on the order should read like this: a named temper, a hardness band, and mechanical results reported for the delivered temper and the delivered thickness. That last clause is what stops a certificate being carried over from a softer coil of the same heat, because the numbers have to belong to the material in front of the press.

Spec 3: Thickness, Width and the Tolerance Band

Our published range runs 0.03 mm to 4.0 mm in thickness and 10 mm to 1500 mm in width, with slit width tolerance of plus or minus 0.2 mm, cut length tolerance of plus or minus 2 mm, and corrective leveling on the slitting service with minimum burr and camber and maximum flatness. These are the numbers to quote, because they describe the service that produces the coil your press receives.

Always state the nominal with its band, and as a percentage where you can. A terminal blank that is nominally 0.30 mm but arrives at 0.32 mm changes both the die clearance and the finished part thickness, and it does so silently, because the press does not stop for a difference it cannot see. The same applies to flatness: strip carrying coil set arrives as a feed variation, and corrective leveling is either written into the order or decided without you.

Two questions belong on the same line: is the strip slit edge or mill edge, and is the width tolerance an absolute band or a percentage? An absolute band means different things at different widths, so one number describes two different products.

Spec 4: Surface Finish and Surface Quality

The published finishes are 2B, BA, 2D, HL, No.4 and 8K, with No.4, hairline and polishing treatments for decorative work, and PVC film coating and paper interleaving listed among the processing services. For terminal strip the finish code is rarely about looks: it decides which face you form against, whether the surface plates evenly, and how much incoming surface quality survives the press.

ASTM A666/A666M is the reference for the standard form and finish of stainless steel strip, and gives the finish codes their meaning. When the order says “2B” with no definition, the buyer is relying on a convention; when it says “2B, protected face identified, paper interleaved”, the coil can be inspected against something visible.

The acceptance rule is what most orders leave out. Roll marks, press-through marks, chatter, scratches and oil spots are all visible on a bright strip and all survive stamping, because the stamp reproduces the surface it was given. Set a rule for what is acceptable on the face that will be visible or plated, and ask whether the film or the interleave protects it, because our published service list includes both and they solve different problems.

Spec 5: Coil Geometry, Edge Condition and Traceability

The fifth lock decides who owns a problem. Our published edge options are slit edge or mill edge, the published services cover decoiling, slitting, cutting, PVC film coating, paper interleaving and surface treatment, and base material is offered from POSCO, TISCO, Baoxin and Qingshan. Locking the coil geometry means stating the inner diameter, the weight, the wrap direction and whether the delivery is slit or cut-to-length.

The edge condition belongs on that line too. A sheared edge carries a work-hardened zone and a burr, and for a terminal the burr is the starting point of a crack if the blank is then bent. Edge conditioning and deburring are services you can specify, and specifying them is cheaper than explaining a rejected batch to the plating line.

Then the certificate: the mill certificate with chemical composition, the mechanical results for the delivered temper and thickness, and the heat number, with the testing reported under a named method such as ASTM A370. The heat number connects a terminal which cracked back to a coil, a heat and a date, and without it every investigation becomes an argument about whose steel it was.

The Five Locks: What to State and What Each One Stops

Five lines on the order, in this order, describe terminal strip well enough to repeat and to check on arrival.

Table 1. The five locks for stamping terminal strip, the published range behind each one, and the failure each prevents.
Lock What to state Published range What it stops
Grade and standard Grade plus the standard it is certified against ASTM/AISI, GB, JIS, EN, KS; 304 written 304, 06Cr19Ni10, SUS304, 1.4301 A certificate describing another material
Temper Temper code, hardness band, results for the delivered temper Annealed, 1/4H, 1/2H, 3/4H, H; hard precision to FH, EH, SH Spring-back no die can absorb
Dimensions Nominal thickness and width with their bands, plus flatness 0.03 mm to 4.0 mm thick, 10 mm to 1500 mm wide, width plus or minus 0.2 mm Silent drift in clearance and part thickness
Surface Finish code, protected face, interleave, defect rule 2B, BA, 2D, HL, No.4, 8K; PVC film and paper interleaving Roll marks reproduced on every terminal
Edge and paperwork Edge condition, deburring, coil geometry, certificate and heat number Slit edge or mill edge; minimum burr and camber, maximum flatness; POSCO, TISCO, Baoxin, Qingshan Burred blanks and investigations with nothing to trace

How to Lock the Five Specs Before the First Coil Arrives

  1. Put grade and standard on one line. Name the grade and the standard it is certified against, from the published set of ASTM/AISI, GB, JIS, EN and KS, so the acceptance band and the certificate have something to hang on.
  2. Put the temper on the next line. Name the temper code and the hardness band, annealed through H for the general range and through SH for hard precision, and ask for mechanical results reported for the delivered temper and thickness.
  3. Put the dimensional band, not the nominal. Quote thickness and width with their tolerance bands, convert the width band to a percentage, and state whether corrective leveling is written into the order.
  4. Put the surface condition on the same page. Name the finish code, identify the protected face, say whether the interleave is PVC film or paper, and write the defect rule for the face that will be visible or plated.
  5. Put the edge condition and the document set last. State slit edge or mill edge, whether deburring is required, the coil geometry, and the certificate with composition, mechanical results and heat number.

Send us the part, the thickness, the width and the annual volume, and we will return the grade, temper, tolerance band and finish your process can run, quoted against the published precision 304 stainless steel strips specification. Spec reviews start on the contact page.

Frequently Asked Questions

1. Which five specs matter most for stamping terminal strip?

Grade with its standard, temper, the dimensional band, the surface condition, and the edge with the certificate set. Between them they fix the material identity, the mechanical condition, the geometry, the two faces and the traceability, the only things about a coil that can change a stamped terminal.

2. Is 304 the right grade for terminal strip?

For most terminals, yes. Our published 304 description gives a minimum of 18 percent chromium and 8 percent nickel, good corrosion resistance, excellent formability and wide use in deep drawing, and our precision range also lists 301, 430, 316L and the duplex grades for demanding environments.

3. Should terminal strip be ordered annealed or half hard?

That follows the terminal, not a preference. Annealed forms easily and springs back the most, and the harder tempers from 1/4H up hold a bend and carry the spring-back into your die compensation. Our published hardness options run annealed, 1/4H, 1/2H, 3/4H and H, with hard precision to FH, EH and SH.

4. How tight does the thickness tolerance need to be for a terminal?

Tight enough that the die clearance and the finished part thickness stay inside your drawing. Our published precision range covers 0.03 mm to 4.0 mm in thickness and 10 mm to 1500 mm in width, so quote the band you need against the nominal and confirm it on receipt.

5. Does the surface finish matter if the terminals are plated afterwards?

Yes, because plating reproduces the surface rather than hiding it. A roll mark or chatter pattern pressed into the strip carries through forming and shows under the plating layer, so name the finish code, protect the right face with PVC film or paper interleaving, and write a defect rule.

6. What documents should arrive with the strip?

A mill certificate with chemical composition, mechanical results for the delivered temper and thickness, and the heat number, reported against a named method such as ASTM A370, plus the standards the material is certified against. The heat number is the part that lets a cracked terminal be traced back to a coil, a heat and a date.

About the author

Mr. Chen

Technical Director, WOW Stainless

Mr. Chen is Technical Director at WOW Stainless, specializing in stainless steel material selection, cold rolling applications, and industrial supply solutions. His work turns grade, temper and tolerance requirements into purchase specifications a stamping line can run without surprises.

Published 16 November 2026 · Last verified 16 November 2026 · Thickness 0.03 mm to 4.0 mm, width 10 mm to 1500 mm, finishes 2B, BA, 2D, HL, No.4 and 8K, hardness annealed through H, edge slit or mill edge, standards ASTM/AISI, GB, JIS, EN and KS, PVC film and paper interleaving, and base material from POSCO, TISCO, Baoxin and Qingshan all verified against the precision stainless steel strip range and the precision 304 stainless steel strips product page. Spring-back behaviour, die clearance guidance and surface defect consequences are engineering practice and must be confirmed against the specific part and order. This is sourcing and specification guidance, not a regulatory determination; certification scope and material declarations must be confirmed for the application and destination market before an order is placed. No price, cost, profit or margin figure is quoted.


Post time: Nov-16-2026

Contact Us

FOLLOW US

For inquiries about our products or pricelist, please leave to us and we will be in touch within 24 hours

Inquiry Now